S8TS SERIES

Item			Single operation	Parallel operation
Efficiency (TYP.)			24-V models: 80% TYP. ; 12-V models: 73% TYP. (with rated input, 100% load)
Input	Voltage *1		Ratings: 100 to 240 VAC (Allowable range: 85 to 264 VAC, 80 to 370 VDC *8)
	Frequency *1		50/60 Hz (47 to 63 Hz)
	Current	100 V input	24-V models: 1.0 A max. 12-V models: 0.7 A max.	24-V models: 1.0 A × (No. of Blocks) max. 12-V models: 0.7 A × (No. of Blocks) max.
		200 V input	24-V models: 0.5 A max. 12-V models: 0.4 A max.	24-V models: 0.5 A × (No. of Blocks) max. 12-V models: 0.4 A × (No. of Blocks) max.
	Power factor		24-V models: 0.9 min.; 12-V models: 0.8 min. (with rated input, 100% load)
	Harmonic current emissions		Conforms to EN61000-3-2
	Leakage current	100 V input	0.35 mA max.	0.35 mA × (No. of Blocks) max.
		240 V input	0.7 mA max.	0.7 mA × (No. of Blocks) max.
	Inrush current *5	100 V input	17.5 A max. (for a cold start at 25°C)	17.5 A × (No. of Blocks) max. (for a cold start at 25°C)
		200 V input	35 A max. (for a cold start at 25°C)	35 A × (No. of Blocks) max. (for a cold start at 25°C)
Output *4	Voltage adjustment range		24-V models: 22 to 28 V 12-V models: 12 V ±10% (with V.ADJ) *2
	Ripple		2% (p-p) max.
	Input variation influence		0.5% max. (with 85 to 264 VAC input, 100% load)
	Load variation influence		2% max. (with rated input, 10% to 100% load)	3% max. (with rated input, 10% to 100% load)
	Temperature variation influence		0.05%/°C max. (with rated input and output)
	Startup time		1,000 ms max. (with 100/200 VAC, rated input)
	Hold time *5		20 ms min. (with 100/200 VAC, rated input)
Addi- tional func- tions	Overload protection *5		105% to 140% of rated load current, voltage drop, automatic reset	100% to 140% of rated load current, voltage drop, automatic reset
	Overvoltage protection *5 *6		Yes
	Parallel operation		Yes (Up to 4 Blocks)
	N+1 redundant system		Yes (Up to 5 Blocks)
	Series operation		Yes
	Undervoltage indicator *5		Yes (color: red)
	Undervoltage detection output *5		Yes (open collector output), 30 VDC max., 50 mA max.
Other	Ambient operating temperature *5		Refer to the derating curve in Engineering Data on Data Sheet (with no icing or condensation).
	Storage temperature		-25 to 65°C
	Ambient operating humidity		25% to 85% (Storage humidity: 25% to 90%)
	Dielectric strength		3.0 kVAC for 1 minute (between all inputs and all outputs; detection current: 20 mA)
			2.0 kVAC for 1 minute (between all inputs and PE terminal; detection current: 20 mA)
			1.0 kVAC for 1 minute (between all outputs and PE terminal; detection current: 20 mA)
	Insulation resistance		100 MΩ min. (between all outputs, and all inputs/PE terminal) at 500 VDC
	Vibration resistance *7		10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions
	Shock resistance *7		150 m/s2, 3 times each in ±X, ±Y, and ±Z directions
	Output indicator		Yes (color: green)
	EMI *8	Conducted Emission	Conforms to EN61204-3 EN55011 Class B and based on FCC Class A *9
		Radiated Emission	Conforms to EN61204-3 EN55011 Class B *9
	EMS *8		Conforms to EN61204-3 High severity levels *9
	Approved standards *8		24V model UL Listed: UL508 (Listing, Class2 Output: Per UL1310) (See note 3.) cUL Listed: CSA C22.2 No.107.1 (Class2 Output: Per CSA C22.2 No.223) (See note 3.) EN: EN62477-112V model UL Listed: UL508 (Listing) cUL Listed: CSA C22.2 No.107.1 EN: EN62477-1
	Weight		450 g max.	450 g × (No. of Blocks) max.

*1. Do not use an inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available, but
the rise in the internal temperature of the Power Supply may result in ignition or burning.
*2. Refer to Data sheet for details on adjusting the output voltage for parallel operation. If set to less than −10%, the
undervoltage detection function may operate. Ensure that the output capacity and output current after adjustment do
not exceed the rated output capacity and rated output current respectively. Adjusting V.ADV may cause the output
voltage to exceed the voltage range. When adjusting the output voltage, confirm the actual output voltage from the
Power Supply and be sure that the load is not damaged.
*3. Class 2 approval does not apply to parallel operation.
*4. The output current is specified at power output terminals.
*5. Refer to the Engineering Data on Data sheet for details.
*6. To reset the protection, turn OFF the input power for one minute or longer and then turn it back again.
*7. Be sure to mount End Plates (PFP-M) on both ends of the Power Supply.
*8. The range for compliance with EC Directives and safety standards (UL, EN, etc.) is 100 to 240 VAC (85 to 264 VAC).
*9. The noise level depends on the wiring method and other factors. Insert one clamp filter (the ZCAT2436-1330A from
TDK) as a noise countermeasure on the input line and ground line combined.

Item			Single operation
Efficiency (typical)			73% TYP. (with rated input, 100% load)
Input	Voltage *1		Ratings: 100 to 240 VAC (Allowable range: 85 to 264 VAC, 80 to 370 VDC *7)
	Frequency *1		50/60 Hz (47 to 63 Hz)
	Current	100 V input	0.7 A max.
		200 V input	0.4 A max.
	Power factor		0.8 min. (with rated input, 100% load)
	Harmonic current emissions		Conforms to EN61000-3-2
	Leakage current	100 V input	0.35 mA max.
		240 V input	0.7 mA max.
	Inrush current *5	100 V input	17.5 A max. (for a cold start at 25°C)
		200 V input	35 A max. (for a cold start at 25°C)
Output *3	Voltage adjustment range		5 V ± 10% (with V. ADJ) *2
	Ripple		2% (p-p) max.
	Input variation influence		0.5% max. (with 85 to 264 VAC input, 100% load)
	Temperature variation influence		0.05%/°C max. (with rated input and output)
	Load variation influence		1.5% max. (with rated input, 10% to 100% load)
	Startup time *4		1,000 ms max. (with 100/200 VAC, rated input)
	Hold time *4		20 ms min. (with 100/200 VAC, rated input)
Addi- tional func- tions	Overload protection *4		105% to 140% of rated load current, voltage drop, automatic reset
	Overvoltage protection *4 *5		Yes
	Parallel operation		No
	N+1 redundant system		No
	Series operation		Yes (with the external diode)
	Undervoltage indicator *4		Yes (color: red)
	Undervoltage detection output *4		Yes (open collector output), 30 VDC max., 50 mA max.
Other	Ambient operating temperature *4		Refer to the derating curve in Engineering Data on Data Sheet.
	Storage temperature		-25 to 65°C (with no icing or condensation)
	Ambient operating humidity		25% to 85%, Storage: 25% to 90%
	Dielectric strength		3.0 kVAC, 50/60 Hz for 1 minute (between all inputs and all outputs; detection current: 20 mA)
			2.0 kVAC, 50/60 Hz for 1 minute (between all inputs and PE terminal; detection current: 20 mA)
			1.0 kVAC for 1 minute (between all outputs and PE terminal; detection current: 20 mA)
	Insulation resistance		100 MΩ min. (between all outputs and inputs/PE terminal) at 500 VDC
	Vibration resistance *6		10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions
	Shock resistance *6		150 m/s2, 3 times each in ±X, ±Y, and ±Z directions
	Output indicator		Yes (color: green)
	EMI *7	Conducted Emission	Conforms to EN61204-3 EN55011 Class B and based on FCC Class A
		Radiated Emission	Conforms to EN61204-3 EN55011 Class B
	EMS *7		Conforms to EN61204-3 High severity levels
	Approved standards *7		UL Listed: UL508 (Listing) UL UR: UL60950-1 (Recognition) cUL Listed: CSA C22.2 No.107.1 cUR: CSA C22.2 No.60950-1 EN/VDE: EN50178 (=VDE0160), EN60950-1 (=VDE0805 Teil1)
	Weight		450 g max.